Revista UIS Ingenierías

Vol. 16 No. 2 (2017): UIS Engineering Journal
Articles

Strength of stainless steel slender beams under concentrated loads by finite elements

PDF (Español (España)) HTML (Español (España))
  • A Asdrúbal,
  • Carlos Graciano,
  • Octavio Andrés González-Estrada
A Asdrúbal
Albatros Ingeniería
Carlos Graciano
Universidad Nacional de Colombia
Bio
Octavio Andrés González-Estrada
Universidad Industrial de Santander
Bio
DOI: https://doi.org/10.18273/revuin.v16n2-2017006

Published 2017-06-10

Keywords

  • Slender beams,
  • concentrated load,
  • stainless steel,
  • ultimate strength

How to Cite

Asdrúbal, A., Graciano, C., & González-Estrada, O. A. (2017). Strength of stainless steel slender beams under concentrated loads by finite elements. Revista UIS Ingenierías, 16(2), 61–70. https://doi.org/10.18273/revuin.v16n2-2017006
Copyright Notice

Abstract

The use of stainless steel in structures has gained momentum in recent years due to its good cost-benefit over time, protection to corrosion, fire resistance and creep resistance greater than that provided by structural steel commonly used in industry. Despite this increase in use there is still some degree of uncertainty and lack of knowledge regarding their application, as steel design codes focus on structural steel. Therefore, the present work reports the results of the numerical study of thin stainless steel beams used in bridges, subjected to concentrated loads, in order to increase the state of the art of this particular application. A finite element model is constructed taking into account the non-linear behavior of the material and the initial imperfections (deflections in the web and residual stresses). The model is validated using experimental data found in the literature, using commercial software MSC.Marc. Then, a parametric study of the influence of the thickness ratio (tf / tw) and load area – length of beam ratio (ss / a) on the ultimate strength is performed. Finally, it is obtained that the use of the stainless steel presents advantages in its post-critical behavior with respect to geometrically similar panels of structural steel, allowing the structural optimization of slender beams for bridges.

PDF (Español (España)) HTML (Español (España))

Downloads

Download data is not yet available.

References

  1. G.Abbruzzese y M. Barteri, Structural Applications of Stainless Steel, Proceedings of I International Conference Super-High Strength Steel, Rome, Italy, Nov. 2005.
  2. ENV 1993-1-4:1996 Eurocode 3 - Design of steel structures – Part 1.4: General rules – Supplementary rules for stainless steels, 2005.
  3. ENV 1993-1-5:2004 Eurocode 3 – Design of steel structures – Part 1.5: General rules – Supplementary rules for planar plated structures without transverse loading, 2004.
  4. E. Unosson, Patch Loading of Stainless Steel Girders: Experiments and Finite Element Analyses, Licentiate Thesis, Lulea University of Technology, Department of Civil and Mining Engineering, Division of Steel Structures, Lulea, Sweden, 2003.
  5. R. Valle Pascual, N. F. Carvajal Monsalve, J. C. Botero Palacio. Evolución de los parámetros geométricos de diseño en puentes construidos con voladizos sucesivos in situ, UIS Ingenierías, vol. 16(1), 86-96, 2017.
  6. O. Lagerqvist, Patch loading- Resistance of Steel Girders Subjected to concentrated Forces, Ph.D. Thesis, Lulea University of Technology, Department of Civil and Mining Engineering, Division of Steel Structures, Lulea, Sweden, 1994.
  7. T.M. Roberts y A.C.B. Newark, Strength of Webs Subjected to Compressive Edge Loading, Journal of Structural Engineering, vol. 123(2), pp. 176-183, 1997.
  8. E.Maiorana, A. Miazzon y L. Briseghella, Web Buckling, Patch Loading and Launching Bridges, Proceedings of I International Conference Super-High Strength Steel, Rome, Italy, Nov. 2005.
  9. E. Mirambell and E. Real, On the Calculation of Deflections in Structural Stainless Steel Beams: An Experimental and Numerical Investigation, Journal of Constructional Steel Research, vol. 54(1), pp. 109–133, 2000.
  10. E. Real and E. Mirambell, Flexural Behaviour of Stainless Steel Beams, Engineering Structures, vol. 27(10), pp. 1465–1475, 2005.
  11. I. Estrada, E. Real y E. Mirambell, General Behaviour and Effect of Rigid and Non-Rigid End Post in Stainless Steel Plate Girders Loaded in Shear. Part I: Experimental Study, Journal of Constructional Steel Research, vol. 63(7), pp. 970-984, 2006.
  12. I. Estrada, E. Real y E. Mirambell, General Behaviour and Effect of Rigid and Non-Rigid End Post in Stainless Steel Plate Girders Loaded in Shear. Part II: Extended Numerical Study and Design Proposal, Journal of Constructional Steel Research, vol. 63(7), pp. 985-996, 2006.
  13. E. Real, E. Mirambell y I. Estrada, Shear Response of Stainless Steel Plate Girders, Engineering Structures, vol. 29(7), pp. 1626-1640, 2007.
  14. Y.C. Oh, D.G. Bae, J.Y. Ko. Basic Research for Resistance Prediction of Aluminium Alloy Plate Girders Subjected to Patch Loading. Journal of the Korean Society of Marine Environment & Safety. 2014;20(2):218-27.
  15. A. Reis, N. Lopes, P. Vila Real. Numerical study of steel plate girders under shear loading at elevated temperatures, Journal of Constructional Steel Research, 117, pp. 1-12, 2016.
  16. J. K. Sonu, K. D. Singh. Shear characteristics of Lean Duplex Stainless Steel (LDSS) rectangular hollow beams, Structures. Vol. 10, pp. 13-29, 2017.
  17. A. M. Agredo Chávez, S. J. Sarmiento Nova, A. Viviescas Jaimes. Evaluación de la rigidez a flexión de puentes de viga-losa en concreto presforzado a partir de pruebas de carga. Caso de estudio: puente La Parroquia, vía La Renta-San Vicente de Chucurí, UIS Ingenierías, vol. 15(2), 2016.
  18. K. J.R. Rasmussen, Full Range Stress-Strain Curves for Stainless Steel Alloys, Journal of Constructional Steel Research; vol. 59(1), pp. 47-61, 2003.

Most read articles by the same author(s)

<< < 1 2